NEO Z-Wave Plus Smart Light Switch User Manual

1. Entwodiksyon

This manual provides comprehensive instructions for the installation, setup, operation, and maintenance of your NEO Z-Wave Plus Smart Light Switch. This intelligent device allows for remote control through a Z-Wave network and radio waves, integrating seamlessly into your smart home system. It requires a Z-Wave gateway controller to function.

The switch features two touch buttons, each capable of controlling an independent relay to turn devices on or off. Each gang supports a maximum of 16A. You can set timers for automated lighting and control the switch remotely.

2. Enfòmasyon sou Sekirite

• AVÈTISMAN: Risk pou chòk elektrik. Se sèlman yon elektrisyen kalifye oswa yon moun ki gen yon bon konpreyansyon sou sistèm elektrik ki ta dwe fè enstalasyon an.
• Disconnect power at the circuit breaker or fuse box before installation.
• Asire w tout koneksyon fil yo byen fèm epi konfòm ak kòd elektrik lokal yo.
• Do not exceed the maximum load rating of 16A per gang.
• Aparèy sa a fèt pou itilize andedan kay la sèlman.
• Kenbe lwen dlo ak imidite twòp.

3. Pwodwi souview

The NEO Z-Wave Plus Smart Light Switch features a sleek touch panel design with integrated indicator lights for status feedback.

Figi 3.1: Devan view of the NEO Z-Wave Plus Smart Light Switch, showing two touch-sensitive circles.

Figi 3.2: Side view illustrating the thin 1mm tempered glass panel of the switch, highlighting its anti-shock and bending strength properties.

Figure 3.3: Detailed technical drawing showing the dimensions (120mm x 74mm x 37mm) and internal components of the smart light switch.

4. Enstalasyon

Before beginning installation, ensure the power is OFF at the circuit breaker. This device is designed for in-wall installation in a standard electrical box.

4.1 Dyagram fil elektrik

The switch requires Live (Line), Load, and Neutral connections. A ground wire should also be connected for safety.

Figure 4.1: Simplified wiring diagram showing connections for Live, Load, and Neutral wires. Consult a qualified electrician if unsure.

4.2 Etap enstalasyon yo

1. Fèmen pouvwa: Locate the circuit breaker controlling the switch location and turn it OFF. Verify power is off using a voltage tèsteur.
2. Retire ansyen switch la: Carefully remove the existing wall plate and switch from the electrical box. Disconnect the wires.
3. Wire the NEO switch: Connect the wires to the corresponding terminals on the NEO Z-Wave Plus Smart Light Switch.
   • Connect the Live (Line) wire to the 'L' terminal.
   • Connect the Load wire(s) to the 'L1' and 'L2' terminals (for 1st and 2nd gang respectively).
   • Connect the Neutral wire to the 'N' terminal.
   • Connect the Ground wire to the ground screw in the box.

   Note: Some users have reported issues with terminal design and mounting. Ensure wires are neatly tucked into the electrical box to prevent interference with the mounting plate. Spacers or washers may be needed between the back plate and the wall if the main unit clips do not seat properly.

4. Monte switch la: Secure the switch into the electrical box using the provided screws.
5. Attach faceplate: Snap the glass faceplate onto the switch module.
6. Retabli kouran an: Remete kouran an nan disjonktè a.

5. Z-Wave Network Setup

The NEO Z-Wave Plus Smart Light Switch must be included (paired) into a Z-Wave network to enable smart control features. It works with most Z-Wave hubs, including SmartThings, Vera, Fibaro, HomeSeer, Iris, and Aeotec.

5.1 Inclusion (Pairing)

1. Ensure your Z-Wave gateway controller is in inclusion mode (refer to your gateway's manual for specific instructions).
2. On the NEO Smart Light Switch, quickly press one of the touch buttons three times. The indicator light will flash to confirm inclusion mode.
3. The gateway will detect and add the device. Once successfully included, the indicator light will stop flashing and show its normal status.

5.2 Exclusion (Unpairing)

1. Ensure your Z-Wave gateway controller is in exclusion mode.
2. On the NEO Smart Light Switch, quickly press one of the touch buttons three times. The indicator light will flash to confirm exclusion mode.
3. The gateway will remove the device from the network.

6. Operasyon Enstriksyon

The NEO Smart Light Switch offers both manual touch control and remote Z-Wave control.

6.1 Manyèl Kontwòl

Simply touch the circular icons on the glass panel to toggle the connected lights or devices ON/OFF.

Figure 6.1: Indicator lights on the touch panel. When power is ON, the LED is red. When power is OFF, the LED is blue.

6.2 Kontwòl a distans atravè Z-Wave Hub

Once paired with your Z-Wave hub, you can control the switch remotely using your hub's mobile application or other integrated smart home systems. This allows for scheduling, scene creation, and control from anywhere.

Figure 6.2: Illustration of a smartphone app controlling the smart light switch through a Z-Wave hub, enabling remote management.

7. Antretyen

The NEO Z-Wave Plus Smart Light Switch requires minimal maintenance.

• Netwayaj: To clean the glass panel, gently wipe it with a soft, damp twal. Pa sèvi ak pwodui netwayaj abrazif oswa solvan, paske sa yo ka domaje sifas la.
• Mizajou mikrolojisyèl: Check your Z-Wave hub's documentation for information on potential firmware updates for connected devices.

NAN. Depanaj

If you encounter issues with your NEO Z-Wave Plus Smart Light Switch, refer to the following common problems and solutions:

9. Espesifikasyon

10. Garanti ak sipò

For warranty information and technical support, please refer to the documentation included with your product packaging or visit the official NEO websit. Kenbe resi acha ou pou reklamasyon garanti.