Geko 6T Bottle Jack (Model G01053) User Manual

1. Pwodwi souview

The Geko 6T Bottle Jack (Model G01053) is a robust hydraulic lifting device designed for heavy goods and industrial vehicles. It features a lifting capacity of up to 6 tons and is constructed from high-quality alloy steel for durability and reliability.

Figure 1: Geko 6T Bottle Jack with its two-piece handle.

Figi 2: Side view of the Geko 6T Bottle Jack, highlighting its compact design.

2. Enfòmasyon enpòtan sou sekirite

Read and understand all safety warnings and operating instructions before using this bottle jack. Failure to follow these instructions may result in property damage, personal injury, or death.

Prekosyon Sekirite Jeneral

• Always operate the jack on a hard, level surface.
• Ensure the load is centered on the jack saddle.
• Never exceed the rated lifting capacity of 6 tons.
• Do not use the jack as a permanent support device. Always use appropriate jack stands to support the load after lifting.
• Keep hands and feet clear of the jack and the load during operation.
• Mete ekipman pwoteksyon pèsonèl (PPE) ki apwopriye, tankou linèt sekirite ak gan.
• Enspekte krik la pou wè si li domaje oswa si li mete anvan chak itilizasyon. Pa sèvi avè l si li domaje.
• Kenbe timoun ak moun ki pa otorize lwen zòn travay la.
• Pa modifye Jack la nan okenn fason.

Lifting and Lowering Safety

• Asire w ke fren pakin machin nan angaje epi wou yo byen bloke anvan ou leve li.
• Leve sèlman nan zòn ki espesifye pa manifakti machin nan.
• Bese chaj la tou dousman ak anpil prekosyon.

3. Enstalasyon

Before using the Geko 6T Bottle Jack, ensure it is properly prepared for operation.

Debalaj ak enspeksyon

1. Carefully remove the jack and its components from the packaging.
2. Inspect the jack for any signs of shipping damage. If damage is found, do not use the jack and contact your supplier.
3. Verify that all components, including the two-piece handle, are present.

Rasanble manch lan

1. Insert the smaller handle section into the larger handle section.
2. Ensure the handle is securely connected before use.

4. Operasyon Enstriksyon

Follow these steps for safe and effective operation of your Geko 6T Bottle Jack.

Lifting a Load

1. Preparasyon: Position the jack on a hard, level surface directly under the lifting point of the load as specified by the manufacturer. Ensure the load is stable and cannot roll or shift.
2. Close Release Valve: Turn the release valve (typically a screw or knob at the base) clockwise until it is firmly closed. Do not overtighten.
3. Position Jack: Ensure the jack saddle is centered under the lifting point.
4. Manch ponp: Insert the handle into the pump sleeve. Pump the handle up and down steadily to raise the jack's ram and lift the load.
5. Monitor Lift: Continue pumping until the load reaches the desired height. Do not lift beyond the maximum extension marked on the ram.
6. Chaj sekirite: Immediately place appropriate jack stands under the load for support. The jack is for lifting only, not for sustained support.

Bese yon chaj

1. Leve yon ti kras: If the load is on jack stands, slightly raise the load with the bottle jack to remove pressure from the stands.
2. Retire sipò Jack yo: Carefully remove the jack stands from under the load.
3. Open Release Valve: Slowly turn the release valve counter-clockwise to gradually lower the load. Control the descent speed by adjusting how much the valve is opened.
4. Desann konplè: Continue lowering until the load is fully supported on the ground or its wheels.
5. Retract Ram: Once the load is fully lowered, fully open the release valve and gently push the ram down if it does not retract completely on its own.

5. Antretyen

Regular maintenance ensures the longevity and safe operation of your Geko 6T Bottle Jack.

Lubrifikasyon

• Periodically lubricate moving parts, such as the pump mechanism and ram, with light machine oil.
• Check the hydraulic oil level every three months. To do this, fully lower the ram, remove the oil filler plug, and ensure the oil level is just below the filler hole. Top up with hydraulic jack oil if necessary.

Netwayaj ak Depo

• Keep the jack clean and free from dirt, grease, and moisture.
• Store the jack in a dry, protected area with the ram fully retracted.

Enspeksyon

• Before each use, inspect the jack for any signs of damage, leaks, or wear. Pay close attention to welds, the ram, and the base.
• If any damage is found, do not use the jack and have it repaired by qualified personnel.

NAN. Depanaj

This section addresses common issues you might encounter with your Geko 6T Bottle Jack.

If you encounter problems not listed here or if solutions do not resolve the issue, contact Geko customer support or a qualified service technician.

7. Espesifikasyon

• Modèl: G01053
• Mak: Geko
• Kapasite pou leve: 6 tòn
• Materyèl: Alloy Steel
• Koulè: Nwa
• Pwa atik: 4.08 Kilogram
• Dimansyon pake: 41 x 35 x 35 cm
• Manifakti: Konpayi Handlowa GEKO
• International Article Number (EAN): 05901477113673

8. Garanti ak sipò

Geko products are manufactured to high standards and are subject to rigorous quality control.

Enfòmasyon sou Garanti

Specific warranty terms and conditions may vary by region and retailer. Please refer to your purchase documentation or contact your retailer for detailed warranty information. Keep your proof of purchase for any warranty claims.

Sipò pou Kliyan

For technical assistance, spare parts, or service inquiries, please contact your local Geko distributor or the retailer from whom you purchased the product.

Manufacturer: Firma Handlowa GEKO