1. Entwodiksyon ak souview
This manual provides detailed instructions for the safe installation, operation, and maintenance of your ET2 Blade-19W LED Pendant Light. The Blade-19W features a sleek, half-inch aluminum blade design with an integrated LED board, creating a distinct lighting effect. Please read this manual thoroughly before proceeding with installation or use.
Figure 1: ET2 Blade-19W LED Pendant Light
2. Enfòmasyon sou Sekirite
- AVÈTISMAN: Risk pou chòk elektrik. Dekonekte kouran an nan disjonktè a oswa bwat fizib la anvan enstalasyon oswa antretyen.
- Tout koneksyon elektrik yo dwe an akò avèk estanda Kòd Elektrik lokal yo ak nasyonal la (NEC). Si ou pa abitye avèk koneksyon fil elektrik ki kòrèk yo, konsilte yon elektrisyen kalifye.
- This fixture is intended for indoor use only. Do not expose to water or moisture.
- Pa eseye modifye aparèy la. Nenpòt modifikasyon ka anile garanti a epi kreye yon danje pou sekirite.
- Manyen aparèy la avèk prekosyon pou evite domaje konpozan LED yo.
3. Pake kontni
Verifye ke tout konpozan yo prezan epi yo pa domaje anvan ou kòmanse enstalasyon an:
- LED Pendant Fixture (1)
- Mounting Canopy (1)
- Mounting Hardware Kit (screws, wire nuts, etc.) (1)
- Manyèl Enstriksyon (1)
4. Enstalasyon ak Enstalasyon
Zouti obligatwa (pa enkli): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, safety glasses.
- Etenn pouvwa: Before starting, ensure the power to the circuit where you are installing the fixture is turned off at the main circuit breaker or fuse box.
- Prepare Sifas Montage: Ensure the ceiling junction box is securely mounted and capable of supporting the fixture's weight (approximately 2.5 lbs).
- Atache Sipò Montaj la: Secure the mounting bracket (typically pre-attached to the canopy) to the junction box using the provided screws.
- Adjust Pendant Height: The pendant cables are adjustable. Determine the desired hanging height for the fixture. Adjust the cable length by pressing the pin on the canopy's cable grip and sliding the cable to the desired length. Ensure both cables are adjusted evenly.
- Fè koneksyon elektrik: Connect the fixture's wires to the corresponding wires from the junction box using the provided wire nuts.
- Konekte a nwa fil aparèy pou a nwa (Live) supply wire.
- Konekte a blan fil aparèy pou a blan (Neutral) supply wire.
- Konekte a green/bare copper fil aparèy pou a green/bare copper (Ground) supply wire.
- Mòn Canopy: Carefully push the canopy up to the ceiling, aligning the mounting screws on the bracket with the holes in the canopy. Secure the canopy in place with the decorative nuts or screws provided.
- Retabli pouvwa: Yon fwa enstalasyon an fini, retabli kouran an nan disjonktè a.
Figure 2: Product Dimensions and Canopy Details
5. Operasyon Enstriksyon
The ET2 Blade-19W LED Pendant Light is designed for simple operation. Once properly installed and powered, the light can be controlled via a remote control (if supplied with your specific model) or a standard wall switch connected to the fixture's circuit.
- Limen/Etenyen: Use the wall switch or remote control to turn the light on or off.
- Koulè limyè: This fixture emits a warm white light.
6. Antretyen
To ensure the longevity and appearance of your pendant light, follow these simple maintenance guidelines:
- Netwayaj: Toujou dekonekte kouran an anvan ou netwaye li. Siye aparèy la avèk yon twal mou epi sèk. Pa sèvi ak pwodui netwayaj abrazif, solvan, oswa pwodui poli paske yo ka domaje fini an oswa konpozan elektrik yo.
- Poul: The integrated LED light source is designed for long-term use and is not user-replaceable. Do not attempt to open or service the LED module.
NAN. Depanaj
Si lanp pandye ou a pa fonksyone byen, gade pwoblèm ak solisyon komen sa yo:
| Pwoblèm | Kòz posib | Solisyon |
|---|---|---|
| Limyè pa limen. | Pa gen pouvwa nan aparèy la. | Check the circuit breaker or fuse. Ensure the wall switch is in the ON position. Verify all electrical connections are secure. |
| Limyè flickers oswa dim. | Koneksyon fil elektrik ki lach. | Turn off power and check all wire connections for tightness. |
| Fixture is damaged. | Physical damage during installation or shipping. | Contact customer support for assistance. Do not attempt to repair. |
8. Espesifikasyon
| Karakteristik | Detay |
|---|---|
| Mak | ET2 |
| Nimewo Modèl | E22903-AL |
| Dimansyon (L x W x H) | 32"L x 0.5"L x 3"H |
| Pwa atik | 2.5 liv |
| Materyèl | Aliminyòm |
| Fini Kalite | Aliminyòm fwose |
| Sous limyè | dirije |
| Kantite sous limyè | 1 |
| Wattage | 19 wat |
| Voltage | 120 Volts |
| Koulè limyè | Blan cho |
| Endèks rann koulè (CRI) | 80+ |
| Kalite aliye | Mòn plafon |
| Kalite enstalasyon | Semi-Flush Mount |
| Itilizasyon Andedan kay la / Deyò | Andedan kay la |
| Metòd kontwòl | Remote |
9. Garanti ak sipò
This ET2 Blade-19W LED Pendant Light is covered by a Garanti limite manifakti 1 ane a soti nan dat acha a. Garanti sa a kouvri domaj nan materyèl ak atizan konn fè nan itilizasyon nòmal.
For warranty claims, technical support, or replacement parts, please contact ET2 customer service. Keep your purchase receipt as proof of purchase.
Enfòmasyon pou kontakte:
Please refer to the ET2 official website or your retailer's contact information for the most current support details.