Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump User Manual

1. Entwodiksyon

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump. This high-capacity pump is engineered to boost water pressure from city water sources or draw water from lakes and streams for various sprinkling and irrigation applications. It features a robust 1-1/2 HP dual voltage motor and a corrosion-resistant thermoplastic construction, ensuring durability and reliable performance. The pump is self-priming after its initial fill with water, simplifying setup.

Image 1.1: The Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump, showcasing its compact design and durable thermoplastic housing.

2. Enfòmasyon sou Sekirite

Read and understand all safety warnings and instructions before installing or operating this pump. Failure to follow these instructions can result in electric shock, fire, serious injury, or death.

• Sekirite elektrik: Always disconnect power before servicing the pump. Ensure the pump is properly grounded. All electrical wiring should be performed by a qualified electrician and comply with local codes. Do not operate the pump with a damaged cord or plug.
• Sekirite dlo: Never run the pump dry, as this can cause severe damage. Protect the pump and plumbing from freezing temperatures to prevent cracking and leaks.
• Sekirite jeneral: Wear safety glasses when working with the pump. Keep children and unauthorized persons away from the operating area. Do not use this pump for flammable or corrosive liquids.

3. Pake kontni

Lè w ap debale l, verifye si tout konpozan yo la epi yo pa domaje. Pakè a ta dwe genyen:

• Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump (1 unit)
• Manyèl Itilizatè (dokiman sa a)

4. Enstalasyon

Bon enstalasyon enpòtan anpil pou pèfòmans ak lonjevite ponp lan.

4.1 Kote

• Enstale ponp lan sou yon sifas ki plat e solid pou minimize vibrasyon.
• Choose a location that is protected from direct sunlight, rain, and freezing temperatures.
• Ensure adequate ventilation around the motor for cooling.

4.2 Piping Connections

• Use appropriate pipe sizes for the inlet and outlet to ensure optimal flow and prevent cavitation.
• Apply thread sealant to all pipe connections to prevent air leaks, especially on the suction side.
• Install a foot valve with a strainer on the end of the suction line if drawing water from a lake or stream to prevent debris from entering the pump and to maintain prime.
• Install a check valve on the discharge side if necessary to prevent backflow.

4.3 Koneksyon elektrik

• The pump features a dual voltage motor (115V or 230V). Ensure the motor is wired for the correct voltage supply available. Refer to the motor's wiring diagram for specific instructions.
• Connect the pump to a dedicated, properly fused electrical circuit.
• Ensure the pump is properly grounded to prevent electrical shock hazards.

4.4 Priming ponp lan

Before initial operation, the pump must be primed:

1. Remove the priming plug located on top of the pump casing.
2. Ranpli ponp c laasing completely with water until it overflows.
3. Ranplase bouchon amorsaj la byen fèm.
4. Ensure all valves on the suction and discharge lines are open.

5. Operasyon Enstriksyon

Yon fwa ponp lan enstale epi amorse, li pare pou fonksyone.

5.1 Kòmanse ponp lan

1. Verify that all connections are tight and there are no visible leaks.
2. Ensure the suction line is submerged in water (if drawing from a source) and the discharge line is open.
3. Turn on the electrical power to the pump. The pump should start and begin moving water.
4. Monitor the pump for the first few minutes of operation for any unusual noises or vibrations.

5.2 Sispann ponp lan

To stop the pump, simply turn off the electrical power supply.

6. Antretyen

Antretyen regilye asire pèfòmans optimal epi pwolonje lavi ponp ou a.

6.1 Tèks regilye

• Periodically inspect the pump and piping for any signs of leaks, corrosion, or damage.
• Clean any debris from the suction strainer (if applicable) to maintain proper flow.
• Ensure the motor's ventilation openings are clear of obstructions.

6.2 Preparasyon pou ivè (pou klima frèt)

If the pump will be exposed to freezing temperatures, it must be drained to prevent damage:

1. Dekonekte pouvwa ponp lan.
2. Remove the drain plug(s) from the pump casing and any low points in the piping system.
3. Kite tout dlo a koule nèt.
4. Store the pump in a dry, protected area if possible, or ensure all plugs are reinstalled loosely to allow for air circulation.

NAN. Depanaj

Seksyon sa a bay solisyon pou pwoblèm komen ou ka rankontre.

8. Espesifikasyon

Technical details for the Everbilt 1-1/2 Hp Thermoplastic Sprinkler Pump.

• Manifakti: Everbilt
• Nimewo Modèl: EFLS15-HD
• Nimewo Pati: EFLS15-HD
• Koulè: Nwa
• Style: Anwo tè
• Materyèl: Plastik, Polipropilèn (PP)
• Kalite sous pouvwa: AC/DC
• Voltage: 115 Volts (AC) / 230 Volts (AC) (Dual Voltage)
• Puisans: 1-1/2 HP
• Ponpe Kapasite: Up to 4020 GPH (Gallons Per Hour)
• Maximum Lifting Height (Suction Depth): Jiska 20 pye
• Kantite pake atik: 1
• Pwa atik: 19.5 kg
• Dimansyon pwodwi: 76.2 x 40.64 x 40.64 cm (Longè x Lajè x Wotè)
• UPC: 856594003961
• Dat premye disponib: 22ye jen 2015

9. Garanti ak sipò

For warranty information, technical support, or replacement parts, please contact Everbilt customer service. Keep your purchase receipt as proof of purchase for any warranty claims. Detailed contact information can typically be found on the product packaging or the official Everbilt websit.