ICM Controls SC1600L Simple Comfort Non-Programmable Heat Only Thermostat User Manual

Entwodiksyon

This manual provides detailed instructions for the installation, operation, and maintenance of your ICM Controls SC1600L Simple Comfort Non-Programmable Heat Only Thermostat. This thermostat is designed for use with single-stage heating systems and features a backlit display for easy readability. Please read this manual thoroughly before installation and operation to ensure proper use and to prevent damage to the unit or your heating system.

Enfòmasyon sou Sekirite

• Always turn off power to the heating system at the main fuse or circuit breaker panel before installing or servicing the thermostat.
• This thermostat is designed for 24 VAC heating systems only. Do not use it with line voltage systems (120/240 VAC).
• Se yon teknisyen kalifye ki ta dwe fè enstalasyon an si ou pa sèten sou nenpòt etap.
• Pa kout sikwi tèminal batri yo.
• Jete pil yo selon règleman lokal yo.

Kontni pake

• ICM Controls SC1600L Thermostat Control Unit
• Materyèl pou monte (vis ak lank miray)
• Manyèl itilizatè

Enstalasyon ak Enstalasyon

1. Chwazi yon Kote

Enstale tèmosta a apeprè 5 pye (1.5 mèt) anlè planche a nan yon zòn ki gen bon sikilasyon lè. Evite kote ki toupre sous chalè (lamps, limyè solèy la, chemine), kouran lè frèt (fenèt, pòt), oswa zòn ki pa gen bon sikilasyon lè.

2. Power Disconnection

Before beginning installation, ensure the power to your heating system is completely turned off at the circuit breaker or fuse box.

3. Retire ansyen tèmosta a

1. Retire kouvèti ansyen tèmosta a avèk prekosyon.
2. Note the wire connections. This thermostat is designed for 2-wire heat-only systems. Typically, these wires are connected to terminals labeled 'R' and 'W'. Take a picture or label the wires for reference.
3. Disconnect the wires and remove the old thermostat's mounting plate from the wall.

4. Enstalasyon Nouvo Tèmosta a

1. Separate the front cover from the backplate of the SC1600L thermostat.
2. Position the backplate against the wall, feeding the wires through the opening. Mark the mounting holes.
3. Drill pilot holes if necessary and secure the backplate to the wall using the provided screws.

5. fil elektrik

Connect the two heating system wires to the terminals on the SC1600L backplate. This thermostat typically uses two wires: one for power (often labeled 'R' or 'Rh') and one for the heating call (often labeled 'W'). Ensure connections are secure.

6. Enstalasyon batri

This thermostat is battery-powered. Insert the required batteries (typically 2 AA batteries, not included) into the battery compartment on the back of the front cover, observing the correct polarity (+/-). The display should illuminate.

7. Attaching the Front Cover

Carefully align the front cover with the mounted backplate and snap it into place.

Image: The ICM Controls SC1600L thermostat installed on a wall, showing its digital display and control buttons.

8. Power Restoration

Restore power to your heating system at the main fuse or circuit breaker panel.

Enstriksyon Operasyon

1. Montre souview

The large digital display shows the current room temperature. When adjusting the setpoint, the desired temperature will be displayed temporarily.

2. Mete tanperati a

• Sèvi ak la UP (▲) ak DESANN (▼) arrow buttons located next to the display to adjust the desired temperature (setpoint).
• Each press of the button will change the setpoint by one degree Fahrenheit.
• The thermostat will automatically maintain the set temperature.

3. System Mode Switch (Off/Heat)

Locate the slide switch at the bottom of the thermostat. This switch controls the system mode:

• OFF: The heating system is turned off. The thermostat will not call for heat.
• CHALÈ: The thermostat will operate the heating system to maintain the set temperature.

4. Operasyon ekleraj dèyè

The display backlight will activate when any button is pressed, providing improved visibility in low-light conditions. The backlight will automatically turn off after a short period of inactivity.

Imaj: Yon imaj detaye view of the SC1600L thermostat's controls and display.

Antretyen

1. Ranplasman batri

The thermostat is battery-powered. When the battery icon appears on the display, it indicates that the batteries are low and need to be replaced. To replace batteries:

1. Gently pull the front cover of the thermostat away from the wall plate.
2. Retire pil fin vye yo epi mete nouvo, asire w ke polarite a kòrèk.
3. Snap the front cover back onto the wall plate.

Nòt: Replacing batteries typically does not affect the set temperature, but it is good practice to verify the setting after replacement.

2. Netwayaj

Netwaye deyò tèmosta a avèk yon twal mou.amp twal. Pa sèvi ak pwodui netwayaj abrazif oswa solvan. Evite flite likid dirèkteman sou tèmosta a.

Depanaj

Espesifikasyon

• Modèl: SC1600L
• Mak: Kontwòl ICM yo
• Kalite kontwòl: Ki pa Peye-pwogramasyon
• Kalite kontwòl tanperati: Chofaj
• Sous pouvwa: Batri Powered
• Voltage: 24 Volts
• Kalite ekspozisyon: LCD ak ekleraj
• Metòd kontwòl: Kontwòl bouton
• Kalite materyèl: Plastik
• Kalite montaj: Panel Mount

Enfòmasyon sou Garanti

ICM Controls products are manufactured to high standards and are backed by a limited warranty. For specific warranty details, including duration and coverage, please refer to the warranty card included with your product or visit the official ICM Controls websit la. Kenbe prèv acha ou pou reklamasyon garanti.

Sipò

If you have any questions or require technical assistance with your ICM Controls SC1600L thermostat, please contact ICM Controls customer support. Contact information can typically be found on the product packaging or the official ICM Controls websit.