ELRO SA50M Wireless Magnetic Contact Sensor User Manual

1. Entwodiksyon

Thank you for choosing the ELRO SA50M Wireless Magnetic Contact Sensor. This device is designed to enhance the security of your home or office by detecting the opening of doors or windows. It is fully compatible with ELRO HA41, HA51, and HA55 alarm systems. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and reliability.

2. Pwodwi souview

The ELRO SA50M consists of two main parts: a sensor unit and a magnetic contact. When these two parts are separated (e.g., when a door or window opens), the sensor triggers an alarm signal to your connected ELRO alarm system.

2.1 Kontni pake a

• 1x ELRO SA50M Wireless Magnetic Contact Sensor (Main Unit)
• 1x Magnetic Contact
• Vis pou monte ak tep adezif
• 1x Battery (CR2032, typically pre-installed or included)
• 1x Manyèl Itilizatè (dokiman sa a)

2.2 Karakteristik kle

• Wireless operation for easy installation.
• Detects opening of doors and windows.
• Compatible with ELRO HA41, HA51, and HA55 alarm systems.
• Ba konsomasyon pouvwa pou lavi batri pwolonje.
• Maximum wireless range of approximately 35 meters (in open air).

2.3 Eleman pwodwi

Figure 1: ELRO SA50M Wireless Magnetic Contact Sensor. This image shows the main sensor unit and the smaller magnetic contact, typically mounted on a door or window frame and the moving part, respectively.

3. Enstalasyon ak Enstalasyon

3.1 Enstalasyon batri

1. Carefully open the main sensor unit's casing.
2. Insert the CR2032 battery, ensuring correct polarity (+ and -).
3. Fèmen casing byen fèm.
4. A small LED indicator may flash briefly to confirm power.

3.2 Pairing with the Alarm System

Before mounting, it is recommended to pair the sensor with your ELRO HA41, HA51, or HA55 alarm system.

1. Put your ELRO alarm system into pairing mode (refer to your alarm system's manual for specific instructions).
2. Activate the SA50M sensor by separating the main unit and the magnetic contact. This simulates an opening event.
3. The alarm system should acknowledge the new sensor. Follow the alarm system's prompts to assign the sensor to a specific zone or name.
4. Test the pairing by separating the sensor and magnet again. The alarm system should register the event.

3.3 Monte Capteur a

Choose a suitable location on a door or window frame. Ensure the main sensor unit and the magnetic contact are aligned and within 1 cm of each other when the door/window is closed.

1. Netwaye sifas la: Asire w ke sifas enstalasyon an pwòp, sèk, epi lis.
2. Pozisyon:
   • Monte la main sensor unit on the fixed part of the door/window frame.
   • Monte la kontak mayetik on the moving part of the door/window.
3. atachman:
   • Sèvi ak tep adezif: Peel off the protective backing from the adhesive tape and firmly press the sensor and magnet onto the desired positions. Hold for 30 seconds.
   • Sèvi ak vis: Mark the screw holes on the mounting surface. Drill pilot holes if necessary. Secure the sensor and magnet using the provided screws.
4. Aliyman Tès: Open and close the door/window several times to ensure the sensor and magnet separate and come together correctly, triggering the alarm system as expected.

4. Fonksyonman Capteur a

The ELRO SA50M operates automatically once installed and paired with your alarm system. When the alarm system is armed:

• If the door or window where the sensor is installed opens, the magnetic contact separates from the main unit.
• The sensor immediately transmits a signal to your ELRO alarm system.
• The alarm system will then trigger its programmed response (e.g., siren, notification).

When the alarm system is disarmed, the sensor will still detect openings but will not trigger an alarm, though it may log the event depending on your alarm system's settings.

5. Antretyen

5.1 Ranplasman batri

The sensor is powered by a CR2032 lithium coin cell battery. When the battery is low, your alarm system may indicate a low battery warning for the specific sensor. Replace the battery as follows:

1. Carefully open the main sensor unit's casing.
2. Retire ansyen batri CR2032 la.
3. Insert a new CR2032 battery, observing correct polarity.
4. Fèmen casing byen fèm.
5. Test the sensor to ensure it is functioning correctly and the low battery warning has cleared on your alarm system.

Nòt: Jete pil yo itilize yon fason responsab selon règleman lokal yo.

5.2 Netwayaj

Wipe the sensor and magnet with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the device.

5.3 Tès Regilye

It is recommended to test your magnetic contact sensors periodically (e.g., monthly) to ensure they are functioning correctly. Arm your alarm system and then open the door/window where the sensor is installed to verify that the alarm triggers.

NAN. Depanaj

Sensor Not Triggering Alarm

• Tcheke batri: Asire w ke batri a byen enstale epi li pa fin dechaje. Ranplase l si sa nesesè.
• Tcheke aliyman: Verify that the main sensor unit and magnetic contact are aligned and within 1 cm when the door/window is closed.
• Tcheke koupi: Ensure the sensor is properly paired with your ELRO alarm system. Re-pair if needed (refer to Section 3.2).
• Entèferans san fil: Large metal objects or other wireless devices nearby can cause interference. Try repositioning the sensor or the alarm system if possible.
• Distans: The sensor might be too far from the alarm system. The maximum range is approximately 35 meters in open air; walls and obstacles reduce this range significantly.

Fo Alam

• Montaj ki lach: Ensure both parts of the sensor are securely mounted and do not shift when the door/window is closed.
• Vibwasyon: Strong vibrations might cause the sensor and magnet to momentarily separate. Re-mount more securely or choose a different location.
• Faktè anviwònman: Extreme temperature changes or humidity can sometimes affect electronics.

7. Espesifikasyon

8. Garanti

ELRO products are covered by a manufacturer's warranty. Please refer to the warranty card included with your purchase or visit the official ELRO websit la pou plis detay sou tèm ak kondisyon garanti a. Kenbe prèv acha ou pou reklamasyon garanti.

9. Sipò

If you encounter any issues or have questions regarding your ELRO SA50M Wireless Magnetic Contact Sensor that are not covered in this manual, please contact ELRO customer support. Contact details can typically be found on the ELRO websit la oubyen sou anbalaj pwodwi a.