Universal 24097 T5 Fluorescent Ballast User Manual

1. Entwodiksyon

This manual provides instructions for the installation, operation, and maintenance of the Universal 24097 T5 Fluorescent Ballast, model B228PUNV115-D001C. This ballast is designed to operate two F28T5 fluorescent lamps with a programmed rapid start method, compatible with 120/277 volt electrical systems. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.

2. Enfòmasyon sou Sekirite

AVÈTISMAN: Risk pou chòk elektrik. Dekonekte kouran an anvan enstalasyon oswa antretyen.

Enstalasyon an dwe fèt pa yon elektrisyen kalifye, dapre kòd elektrik nasyonal ak lokal yo.
Asire vol D' atage matches the ballast's rated voltage (120/277V).
Do not operate the ballast with damaged wiring or if the casing is compromised.
This device is not intended for use with dimmers unless specifically rated for dimming applications.
Kenbe lwen dlo ak damp anviwònman.

3. Enstalasyon ak Enstalasyon

The Universal 24097 ballast is designed for easy integration into fluorescent lighting fixtures. Follow these steps for proper installation:

Dekonekte pouvwa: Before beginning any work, ensure the main power supply to the fixture is turned off at the circuit breaker. Verify with a voltage tèsteur.
Remove Old Ballast (if applicable): Carefully disconnect and remove the existing ballast from the fixture. Note the wiring configuration.
Mount New Ballast: Securely mount the Universal 24097 ballast inside the fixture using appropriate screws or mounting hardware. Ensure it is firmly in place to prevent vibration.
Koneksyon fil elektrik:
Refer to the wiring diagram provided on the ballast label for correct connections. Typically, this involves:
- Konekte a nwa wire to the 120V or 277V (line) input.
- Konekte a blan wire to the neutral input.
- Konekte a wouj epi ble wires to the lamp sockets as indicated for the two F28T5 lamps.
- Asire w tout koneksyon yo byen fèm epi izole ak boulon fil.
Figure 1: Universal 24097 Fluorescent Ballast. This image shows the ballast unit, typically with a wiring diagram label visible on its surface, indicating connection points for power input and lamp rezilta yo.
Enstale Lamps: Insert the two F28T5 fluorescent lamps into their respective sockets.
Retabli pouvwa: Once all connections are secure and lamps are installed, restore power at the circuit breaker.

4. Operasyon Enstriksyon

The Universal 24097 ballast operates automatically once power is supplied. It utilizes a programmed rapid start method, which provides a brief preheat to the lamp cathodes before ignition, extending lamp life and ensuring flicker-free starting.

Upon power-up, the ballast will initiate the lamps.
Si lamps do not light, ensure they are properly seated and power is supplied.
This ballast is designed for continuous operation within its specified temperature range.

5. Antretyen

The Universal 24097 ballast is designed for long-term, maintenance-free operation. However, periodic checks of the lighting fixture are recommended.

Netwayaj: Ensure the ballast and fixture remain free of dust and debris to prevent overheating. Disconnect power before cleaning.
Lamp Ranplasman: Lè w ap ranplase lamps, always disconnect power first. Replace both lamps simultaneously for optimal performance and ballast life. Use only F28T5 lamps.
Enspeksyon fil elektrik: Periodically inspect wiring for any signs of wear, fraying, or loose connections. Address any issues immediately after disconnecting power.

NAN. Depanaj

If you encounter issues with your Universal 24097 ballast, refer to the following troubleshooting guide:

Pwoblèm	Kòz posib	Solisyon
Lamps pa limen.	Pa gen pouvwa nan aparèy. Koneksyon fil elektrik ki lach. Defektye lamps. Ballast ki defektye.	Tcheke disjonktè a ak switch miray la. Verify all wiring connections are secure (power off). Ranplase lamps with new F28T5 lamps. Si lamps are new and wiring is correct, replace ballast.
Lamps flicker or hum.	Pa kòrèk lamp kalite. Lache lamp koneksyon. Aje lamps. Ballast nearing end of life.	Ensure F28T5 lampyo itilize yo. Reseat lamps firmly in sockets. Ranplase lamps. Consider replacing ballast.
Ballast is hot to the touch.	Normal operating temperature. Pòv vantilasyon. Sikwi twò chaje.	Some heat is normal. Ensure fixture has adequate airflow. Consult an electrician if overheating persists or is excessive.

7. Espesifikasyon

Modèl: B228PUNV115-D001C (24097)
Mak: Inivèsèl
Lamp Kalite: F28T5 Fluorescent
Kantite Lamps: 2
Antre Voltage: 120 / 277V AC
Metòd kòmanse: Programmed Rapid Start
Nimewo Pati Manifakti: 24097
ASIN: B0070FFQG6
Dat premye disponib: 22 janvye 2012

8. Garanti ak sipò

For warranty information and technical support, please refer to the official Universal Lighting Technologies websit la oubyen kontakte depatman sèvis kliyan yo. Kenbe resi acha w la pou reklamasyon garanti.

Manifakti: Teknoloji ekleraj inivèsèl

Nimewo Pati: 24097

ASIN: B0070FFQG6

Inivèsèl 24097