Actiontec My Wireless TV WiFi / HDMI Multi-Room Wireless HD Video Kit (MWTV200KIT-01) User Manual

1. Entwodiksyon

The Actiontec My Wireless TV WiFi / HDMI Multi-Room Wireless HD Video Kit (MWTV200KIT-01) provides a solution for wirelessly distributing high-definition video and audio throughout your home. This kit allows you to transmit full 1080p HD and 3D video from an HDMI source device to an HDTV or projector up to 150 feet away, without the need for long HDMI cables. It supports HDCP 2.0 for protected content and includes IR back-channel functionality for controlling your source device remotely.

This manual provides detailed instructions for setting up, operating, and maintaining your My Wireless TV kit, along with troubleshooting tips and product specifications.

2. Ki sa ki nan bwat la

Verify that all components are present in your My Wireless TV kit:

• Wireless HD Video Transmitter
• Wireless HD Video Receiver
• Energy efficient power supplies (x2)
• High-speed HDMI cables (x2)
• IR Blaster kab
• IR reseptè kab
• Remote kontwòl
• Gid pou kòmanse rapid

3. Enstriksyon Enstalasyon

Follow these steps to set up your Actiontec My Wireless TV kit:

3.1. Connect the Transmitter

1. Power Off Source Device: Ensure your HDMI source device (e.g., cable box, Blu-ray player) is powered off.
2. Konekte HDMI: Connect one end of an HDMI cable to the HDMI output port of your source device. Connect the other end of the HDMI cable to the HDMI-AN port on the My Wireless TV Transmitter.
3. Konekte pouvwa: Connect one of the energy-efficient power supplies to the Transmitter's power port and plug it into an electrical outlet.
4. (Optional) HDMI Pass-through: If you wish to connect a local TV to the same source, connect another HDMI cable from the HDMI SOTI (pass-through) port on the Transmitter to your local TV's HDMI input.
5. (Si ou vle) Enstalasyon IR: If you intend to control your source device remotely, plug the IR Blaster cable into the IR SOTI port on the Transmitter. Position the IR Blaster emitter directly over the IR sensor of your source device.

Imaj: Dèyè view of the Actiontec My Wireless TV Transmitter, showing HDMI In, HDMI Out, IR Out, and power ports.

3.2. Konekte Reseptè a

1. Power Off Display: Ensure your HDTV or projector is powered off.
2. Konekte HDMI: Connect the second HDMI cable from the HDMI SOTI port on the My Wireless TV Receiver to an available HDMI input port on your HDTV or projector.
3. Konekte pouvwa: Connect the second energy-efficient power supply to the Receiver's power port and plug it into an electrical outlet.
4. (Si ou vle) Reseptè IR: If you intend to control your source device remotely, plug the IR Receiver cable into the IR IN port on the Receiver. Position the IR Receiver sensor in a location where it can receive signals from your remote control.

Imaj: Dèyè view of the Actiontec My Wireless TV Receiver, showing HDMI Out, IR In, and power ports.

3.3. Power On and Sync

1. Pouvwa sou aparèy: Power on your source device, the My Wireless TV Transmitter, the My Wireless TV Receiver, and your HDTV/projector.
2. Chwazi Antre: On your HDTV/projector, select the HDMI input connected to the My Wireless TV Receiver.
3. Otomatik senkronizasyon: The Transmitter and Receiver should automatically establish a wireless connection. The "Wireless" LED indicator on both units will illuminate when a connection is established.
4. Manual Sync (if needed): If the units do not sync automatically, press the "Sync" button on both the Transmitter and Receiver simultaneously for a few seconds until the "Wireless" LED blinks, then becomes solid.
5. Jwi: Once synced, the video from your source device should appear on your remote display.

4. Operasyon

4.1. ViewKontni

After successful setup and syncing, the content from your HDMI source device will be wirelessly transmitted to the connected HDTV or projector. Ensure the remote display is set to the correct HDMI input.

4.2. Remote Control Functionality (IR Back-channel)

The included IR Blaster and IR Receiver cables enable you to control your source device from the remote display location. Point your source device's original remote control at the My Wireless TV Receiver's IR sensor. The signal will be transmitted back to the Transmitter, which then uses the IR Blaster to control your source device.

4.3. On-Screen Control

The My Wireless TV kit features an on-screen control interface. Use the provided remote control to navigate this interface for source switching and accessing advanced features. Refer to the quick start guide for specific remote control button functions.

5. Antretyen

• Netwayaj: Use a soft, dry cloth to clean the surfaces of the Transmitter and Receiver. Do not use liquid cleaners or aerosols.
• Vantilasyon: Ensure that the units have adequate ventilation. Do not block ventilation openings.
• Mizajou mikrolojisyèl: Periodically check the Actiontec support websit pou mizajou firmwèr pou asire pèfòmans ak konpatibilite optimal.
• Sik pouvwa: If experiencing minor issues, power cycling both the Transmitter and Receiver (unplugging and replugging after 10 seconds) can often resolve them.

NAN. Depanaj

This section addresses common issues you might encounter with your My Wireless TV kit.

6.1. No Picture or Signal

• Tcheke Koneksyon: Ensure all HDMI and power cables are securely connected to both the Transmitter and Receiver, and to your source and display devices.
• Correct Input: Verify that your HDTV or projector is set to the correct HDMI input.
• Estati pouvwa: Confirm that both the Transmitter and Receiver are powered on (power LEDs illuminated).
• Senkronizasyon san fil: Check the "Wireless" LED on both units. If it's not solid, try pressing the "Sync" button on both units simultaneously.
• Aparèy Sous: Ensure your source device is powered on and outputting a signal.
• Entèferans: Wireless transmission can be affected by obstacles (walls, furniture) and other wireless devices (Wi-Fi routers, cordless phones). Try repositioning the units or reducing the distance between them.

6.2. Picture Flickering or Intermittent Signal

• Distans ak Obstak: The wireless signal strength decreases with distance and when passing through multiple walls or dense materials. Try moving the Receiver closer to the Transmitter or ensuring a clearer line of sight.
• Entèferans: Other wireless devices operating on similar frequencies (2.4GHz or 5GHz) can cause interference. Try changing the wireless channel if your units support this feature (check on-screen menu or support documentation).
• Sik pouvwa: Perform a power cycle on both the Transmitter and Receiver.

6.3. Kontwòl remote la pa fonksyone

• IR Cable Placement: Ensure the IR Blaster emitter is directly over the IR sensor of your source device. The IR Receiver should be positioned to receive signals from your remote.
• Liy Vizyon: Ensure there is a clear line of sight between your remote control and the IR Receiver.
• Batri: Check the batteries in your source device's remote control.

6.4. Audio Issues (No Sound or Distorted Audio)

• Koneksyon HDMI: Re-check all HDMI cable connections.
• Anviwònman odyo ekspozisyon an: Verify the audio settings on your HDTV or projector.
• Anviwònman Sous Odyo: Ensure your source device is outputting audio correctly.

7. Espesifikasyon

8. Garanti ak sipò

For technical assistance, warranty information, or to download the latest software and firmware updates, please visit the official Actiontec support websit:

www.actiontec.com/support

Please have your product model number (MWTV200KIT-01) and serial number ready when contacting support.