Steinbach SPS 100-1 Self-Priming Filter Pump User Manual

1. Entwodiksyon

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Steinbach SPS 100-1 self-priming filter pump. Please read all instructions carefully before installation and use. Keep this manual for future reference.

2. Enstriksyon Sekirite

Enfòmasyon enpòtan sou sekirite:

• Toujou dekonekte ponp lan nan ekipman pou kouran an anvan ou fè nenpòt antretyen oswa netwayaj.
• Ensure the electrical installation complies with local regulations and is protected by a Residual Current Device (RCD) with a tripping current not exceeding 30 mA.
• Do not operate the pump if the power cord or plug is damaged. Contact qualified personnel for repairs.
• The pump must be installed on a solid, level surface, protected from direct sunlight and rain.
• Ensure adequate ventilation around the pump motor to prevent overheating.
• Aparèy sa a pa fèt pou itilize pa moun (ki gen ladan timoun) ki gen kapasite fizik, sansoryèl oswa mantal redwi, oswa ki pa gen eksperyans ak konesans, sof si yo te ba yo sipèvizyon oswa enstriksyon konsènan itilizasyon aparèy la pa yon moun ki responsab sekirite yo.
• Timoun yo ta dwe sipèvize pou asire ke yo pa jwe ak aparèy la.

3. Pwodwi souview

The Steinbach SPS 100-1 is a self-priming filter pump designed for efficient water circulation in swimming pool filter systems, such as the Speed Clean Comfort 75. It operates without a built-in timer, offering continuous operation when powered.

Eleman

• Pump body with motor
• Pre-filter basket with transparent lid
• Inlet ak priz koneksyon
• Kab pouvwa ak ploge

Figi 1: Plis paseview of the Steinbach SPS 100-1 Self-Priming Filter Pump.

Figi 2: Close-up view of the pre-filter housing and the inlet connection with a hose attached. The transparent lid allows for easy inspection of the filter basket.

Figi 3: Detaye view of the pre-filter and the threaded inlet connection, ready for hose attachment.

Figure 4: Close-up of the pump's outlet connection with a hose securely fastened, directing filtered water.

Figi 5: Detaye view of the pump's threaded outlet connection, showing the port where the return hose connects.

Figure 6: Product label displaying technical specifications such as model number, voltage, power, and flow rate.

4. Enstalasyon ak Enstalasyon

Proper installation is crucial for the pump's performance and longevity. Refer to your specific filter system manual for detailed plumbing instructions.

4.1 Plasman

• Position the pump as close to the pool as possible, below water level if feasible, to aid in self-priming.
• Ensure the pump is on a stable, level, and dry surface.
• Protect the pump from direct weather exposure (rain, snow, direct sunlight).
• Allow sufficient space around the motor for ventilation and maintenance access.

4.2 Koneksyon plonbri

• Connect the suction line from the pool skimmer/main drain to the pump's inlet (front connection).
• Connect the discharge line from the pump's outlet (top connection) to the filter system's inlet.
• Use appropriate fittings, clamps, and thread sealant (Teflon tape) to ensure watertight connections.
• Avoid kinks or sharp bends in hoses to maintain optimal flow.

4.3 Koneksyon elektrik

• Asire w ke ekipman pou pouvwa a koresponn ak vòltaj ponp lan.tage (230 V).
• Plug the pump into a grounded electrical outlet protected by an RCD.
• Pa sèvi ak kòd ekstansyon sof si li absoliman nesesè epi asire w ke yo apwopriye pou itilizasyon deyò ak pou bezwen pouvwa ponp lan.

5. Operasyon Enstriksyon

5.1 Priming ponp lan

As a self-priming pump, the SPS 100-1 can draw water, but initial priming is recommended for faster startup:

1. Ensure all valves are open, allowing water to flow from the pool to the pump.
2. Remove the transparent lid of the pre-filter.
3. Fill the pre-filter housing completely with water.
4. Replace the lid securely, ensuring the O-ring is properly seated to prevent air leaks.
5. Turn on the pump. It should begin to draw water and expel air. If it does not prime within a few minutes, turn it off, re-check connections, and repeat the priming process.

5.2 Operasyon Nòmal

• Once primed, the pump will continuously circulate water through your filter system.
• Monitor the pressure gauge on your filter (if applicable) to determine when backwashing or filter cleaning is needed.
• This model does not include a timer, so you will need to manually switch it on and off or connect it to an external timer (not included).

6. Antretyen

6.1 Pre-Filter Basket Cleaning

Regularly inspect and clean the pre-filter basket to prevent debris buildup and maintain pump efficiency.

1. Etenn ponp lan epi dekonekte li nan ekipman pou kouran an.
2. Fèmen tout tiyo ki nesesè pou anpeche dlo koule soti nan pisin lan.
3. Unscrew the transparent lid of the pre-filter.
4. Remove the basket and empty any collected debris.
5. Rense panyen an byen avèk dlo.
6. Inspect the O-ring on the lid for damage and ensure it is clean.
7. Replace the basket and securely fasten the lid.

6.2 Winterization

Before freezing temperatures arrive, properly winterize your pump to prevent damage:

• Dekonekte ponp lan soti nan ekipman pou pouvwa a.
• Drain all water from the pump by removing the drain plug (usually located at the bottom of the pump housing).
• Disconnect all hoses and pipes.
• Clean the pre-filter basket and housing.
• Sere ponp lan nan yon kote ki sèk epi ki pa gen jèl.

NAN. Depanaj

8. Espesifikasyon

9. Garanti ak sipò

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Steinbach customer service directly. Keep your proof of purchase for warranty claims.

Enfòmasyon pou kontakte:

• Manufacturer: Steinbach
• Websit: www.steinbach.at (Please check for local support details)