Clover B14A Hot and Cold Bottled Water Dispenser User Manual

1. Entwodiksyon

The Clover B14A Hot and Cold Bottled Water Dispenser provides convenient access to refreshing chilled drinking water and piping hot water. Designed for home or office use, this dispenser features hygienic stainless steel tanks and an efficient cooling and heating system. Please read this manual thoroughly before operation to ensure safe and optimal performance.

2. Enfòmasyon sou Sekirite

• Sekirite elektrik: This appliance operates on 110-120 volts, 50-60 Hz. Ensure the power outlet is properly grounded. Do not use with damaged cords or plugs.
• Sekirite Dlo Cho: The hot water temperature reaches approximately 185°F (85°C). Exercise extreme caution when dispensing hot water to prevent burns. A safety switch is provided for the hot water dispenser.
• Sekirite timoun: Always engage the hot water safety switch when children are present to prevent accidental dispensing of hot water.
• Plasman: Place the dispenser on a flat, stable surface away from direct sunlight, heat sources, and areas with high humidity. Ensure adequate ventilation around the unit.
• Boutèy dlo: Use only standard 5-gallon (18.9-liter) water bottles.
• Antretyen: Debranche aparèy la anvan ou netwaye li oswa fè nenpòt antretyen.

3. Enstalasyon

1. Debake: Retire dispansè a nan anbalaj li avèk prekosyon. Enspekte li pou wè si li gen nenpòt domaj.
2. Plasman: Position the dispenser on a level, sturdy surface. Allow at least 4 inches (10 cm) of clearance from walls for proper ventilation.
3. Enstale plato degoute a: Insert the concealed, lift-out drip tray into its designated slot below the spigots.
4. Netwayaj inisyal: Anvan premye itilizasyon an, netwaye deyò a ak yon twal mou.amp twal.
5. Enstale boutèy dlo a: Remove the protective seal from a new 5-gallon water bottle. Lift the bottle and quickly invert it, placing it firmly onto the bottle support on top of the dispenser. Ensure the bottle is seated correctly to prevent leaks.
6. Sistèm flannen: Before plugging in, dispense at least 1 liter (approximately 4 cups) of water from both the hot and cold spigots to ensure the tanks are filled and to flush any air from the system.
7. Ploge nan: Branche kòd kouran an nan yon priz elektrik 110-120V ki gen koneksyon ak tè.

Figi 1: Konplè view of the Clover B14A water dispenser with a 5-gallon bottle.

4. Operasyon Enstriksyon

1. Pouvwa sou: Once plugged in, the dispenser will begin cooling and heating the water. Allow approximately 15-30 minutes for the water to reach desired temperatures.
2. Distribisyon dlo frèt: Place your cup under the cold water spigot (typically blue). Push the lever to dispense cold water. Release the lever to stop.
3. Distribisyon dlo cho: Place your cup under the hot water spigot (typically red). To dispense hot water, first push the safety switch (often a red button or lever) and then push the main lever. Release both to stop.
4. Chanjman dlo cho: The hot water function can be turned on or off using the switch located on the back of the unit. Turning it off will prevent the water from heating, saving energy and acting as an additional safety measure.
5. Adjusting Cold Water Temperature: The cold water temperature can be adjusted via a thermostat control, usually located on the back of the unit. It allows for a range of 35.6°F to 53.6°F (2°C to 12°C).

Figure 2: Detail of the hot (red) and cold (blue) water spigots with the hot water safety switch.

5. Antretyen

• Netwayaj plato degoute: The drip tray is removable for easy cleaning. Periodically empty and wash the tray with mild soap and water.
• Netwayaj eksteryè: Siye sifas eksteryè yo ak yon mou, damp twal. Pa sèvi ak pwodui netwayaj abrazif oswa solvang.
• Detartraj: Over time, mineral deposits may accumulate in the hot water tank. Consult the manufacturer's website or customer support for recommended descaling procedures.
• Netwayaj tank dlo: For thorough cleaning of the internal water tanks, it is recommended to contact a qualified service technician.

NAN. Depanaj

• Pa gen distribisyon dlo: Ensure the water bottle is properly seated and not empty. Check if the unit is plugged in and powered on.
• Pa gen dlo cho: Verify the hot water switch on the back of the unit is in the 'ON' position. Check if the thermal reset button (often a small red button on the back) needs to be pressed.
• No Cold Water: Ensure the unit is plugged in and the cold water thermostat is set to a desired temperature.
• Fuite: Check the water bottle for cracks or improper seating. Ensure the drip tray is correctly installed.
• bri ki pa nòmal: The unit is designed for quiet operation. If unusual or excessive noise occurs, ensure the unit is on a level surface and not vibrating against a wall. If noise persists, contact customer support.

7. Espesifikasyon

• Modèl: B14A
• Dimansyon (D x W x H): 12.3" x 12.7" x 37.9" (31.2 santimèt x 32.3 santimèt x 96.3 santimèt)
• Pwa: 32 liv (14.5 kg)
• Koulè: Black with Steel side panels
• Voltage: 110-120V
• Frekans: 50-60 Hz
• Tanperati dlo cho: Approximately 185°F (85°C) (non-adjustable)
• Tanperati dlo frèt: 35.6°F - 53.6°F (2°C - 12°C) (adjustable)
• Compatible Bottle Sizes: 5 galon (18.9 lit)
• Materyèl konstriksyon: Nerjaveèi asye, plastik
• Sètifikasyon: CE, NSF, UL, Energy Star Rated
• Degoute Plato: Concealed, lift-out design, high impact, durable ABS. Removable, anti-splash grid.

8. Garanti ak sipò

The Clover B14A Hot and Cold Bottled Water Dispenser comes with a Garanti manifakti limite pou 1 an. For warranty claims, technical assistance, or further inquiries, please contact Clover customer support. Keep your purchase receipt as proof of purchase.