Performance Tool W1612 2.5 Ton Hydraulic Floor Jack User Manual

1. Enfòmasyon sou Sekirite

Always prioritize safety when operating the Performance Tool W1612 hydraulic floor jack. Failure to follow these instructions may result in serious injury or property damage.

• Li Manyèl la: Read and understand all instructions and warnings in this manual before using this product.
• Itilize sou sifas ki di e plat: Operate the jack only on a hard, level surface capable of supporting the load. Avoid uneven or soft ground.
• Do Not Exceed Capacity: Never exceed the rated capacity of 5,000 lbs (2.5 tons).
• Sèvi ak sipò Jack: After lifting the vehicle to the desired height, always support it immediately with appropriately rated jack stands. The hydraulic jack is a lifting device only and is not designed to sustain loads for extended periods.
• Center the Load: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
• Mete Kovèti pou Sekirite: Always wear ANSI-approved safety goggles and heavy-duty work gloves during operation.
• Kenbe klè: Kenbe men, pye ak lòt pati nan kò ou lwen pati k ap deplase yo ak machin nan pandan w ap leve ak desann chay la.
• Enspekte anvan w itilize: Anvan chak itilizasyon, enspekte krik la pou wè si li gen nenpòt domaj, flit, oswa pyès ki lach. Pa sèvi avè l si li domaje.
• Depo apwopriye: Store the jack in a clean, dry place, fully lowered, when not in use.

2. Pwodwi souview

The Performance Tool W1612 is a heavy-duty 2.5 ton (5,000 lb) hydraulic floor jack designed for lifting vehicles. It features a robust steel construction, wide front wheels, and a 360-degree swivel saddle for ease of use.

Konpozan kle:

• Leve bra: The main arm that raises and lowers the vehicle.
• Saddle: The contact point with the vehicle's lifting area.
• Manch: Yo itilize li pou ponpe pou leve epi pou vire pou desann.
• Valv lage: Kontwole vitès desandan krik la.
• Wheels/Casters: Allow for easy positioning and maneuvering.

Figure 1: Performance Tool W1612 2.5 Ton Hydraulic Floor Jack. This image shows the overall design of the yellow hydraulic floor jack with its long handle and wheels.

Figi 2: Side view of the Performance Tool W1612 Hydraulic Floor Jack. This image provides a different angle of the jack, highlighting its low-profile design and robust construction.

3. Enstalasyon

Premye Preparasyon:

1. Debake: Carefully remove the jack from its packaging. Inspect for any shipping damage.
2. Manch Asanble: Insert the handle into the handle socket and secure it according to the instructions provided in the packaging.

Senyen Sistèm Idwolik la:

Air can become trapped in the hydraulic system during shipping or use, affecting performance. Bleeding the system removes this air.

1. Open Release Valve: Vire manch lan nan sans kontrè ak zegwi mont lan pou louvri valv lage a nèt.
2. Manch ponp: Pump the handle 6-8 full strokes to force air out of the system.
3. Close Release Valve: Vire manch lan nan direksyon goch pou fèmen valv la lage.
4. Tès: Test the jack by lifting and lowering it a few times without a load. If the jack does not lift smoothly or to its full height, repeat the bleeding process.

4. Operasyon Enstriksyon

Leve yon machin:

1. Prepare machin: Park the vehicle on a hard, level surface. Engage the parking brake and block the wheels that will remain on the ground.
2. Position Jack: Position the jack directly under the vehicle's designated lifting point. Consult your vehicle's owner's manual for proper lifting points.
3. Close Release Valve: Turn the handle clockwise until the release valve is firmly closed. Do not overtighten.
4. Veyikil leve: Pump the handle up and down to raise the vehicle to the desired height. Ensure the vehicle remains stable during lifting.
5. Fikse ak sipò Jack: Once the vehicle is at the desired height, immediately place appropriately rated jack stands under the vehicle's frame or designated support points.
6. Slightly Lower onto Stands: Slowly turn the handle counter-clockwise to open the release valve, allowing the vehicle to gently rest onto the jack stands. Remove the hydraulic jack once the vehicle is securely supported by the stands.

Desann yon machin:

1. Reposition Jack: If removed, place the hydraulic jack back under the vehicle's lifting point and raise it slightly to take the load off the jack stands.
2. Retire sipò Jack yo: Retire sipò krik yo anba machin nan avèk prekosyon.
3. Veyikil ki pi ba a: Slowly turn the handle counter-clockwise to open the release valve. Control the lowering speed by adjusting how much you open the valve.
4. Fully Lower: Once the vehicle is fully lowered, remove the jack.

5. Antretyen

Regular maintenance ensures the longevity and safe operation of your hydraulic floor jack.

• Nivo likid idwolik: Check the hydraulic fluid level periodically. With the jack fully lowered, remove the oil filler plug. The fluid level should be just below the filler hole. Top up with high-quality hydraulic jack oil if necessary. Do not use brake fluid or motor oil.
• Lubrifikasyon: Lubricate all moving parts and pivot points with light machine oil monthly or as needed.
• Netwayaj: Keep the jack clean and free of dirt, grease, and corrosive materials. Wipe down the ram and pump plungers after each use.
• Depo: Store the jack in a dry, protected area, fully lowered, to prevent rust and seal damage.

NAN. Depanaj

7. Espesifikasyon

• Modèl: W1612
• Kapasite chaj: 5,000 lbs (2.5 Tons)
• Wotè maksimòm pou leve: 19.25 pous
• Minimum Lifting Height: Approximately 5 inches (standard floor jack minimums)
• Materyèl: Alloy Steel
• Pwa atik: 79.7 liv
• Dimansyon pwodwi (L x W x H): 30.6 x 8.6 x 15.4 pous
• Kalite sèvis machin: Machin, kamyon

8. Garanti ak sipò

For warranty information or technical support regarding your Performance Tool W1612 hydraulic floor jack, please refer to the documentation included with your purchase or contact Performance Tool customer service directly. Keep your purchase receipt for warranty claims.

Manifakti: Performance Tool (Wilmar Corporation)

UPC: 039564124778

Dat premye disponib: 1 avril 2004